Toyota 4afe Ecu Pinout – Must See

Drop a comment below (if applicable) or consult the factory Toyota Electrical Wiring Diagram (EWD) for your specific chassis code.

| Pin | Wire Color | Signal Name | Function | | :--- | :--- | :--- | :--- | | | White | IGT | Ignition Timing Signal (from ECU to igniter) | | B02 | Red/White | #10 | Fuel Injector Cylinder #1 | | B03 | Blue | #20 | Fuel Injector Cylinder #2 | | B04 | Yellow | #30 | Fuel Injector Cylinder #3 | | B05 | Brown | #40 | Fuel Injector Cylinder #4 | | B06 | Black/Yellow | FC | Circuit Opening Relay (Fuel Pump Control) | | B07 | Light Green | VSV (CC) | Charcoal Canister Purge VSV | | B08 | - | - | Empty | | B09 | Red/White | +BM | Backup power for ECU memory (constant 12V) | | B10 | Black/Orange | W | Check Engine Light (MIL) Control | | B11 | Blue/White | ACT | Air Conditioning Switch Signal (to ECU) | | B12 | Red/Black | ACMG | A/C Compressor Magnetic Clutch Relay | | B13 | Black | E1 | Sensor Ground (shared with TPS, MAP, etc.) | | B14 | Black/White | E03 | Injector Power Ground | | B15 | Black/White | E04 | Injector Power Ground | | B16 | - | TE1 | Diagnostic Jumper Pin (for flashing CEL codes) | toyota 4afe ecu pinout

Pins B02-B05 (injectors) are switched grounds. The ECU grounds these wires to fire the injectors. You will not see 12V here with the key on. Instead, each wire should show continuity to ground for a brief pulse when cranking. Connector C (12 pins) – Auxiliary & Diagnostics This connector handles extra sensors, tachometer, and diagnostics. Drop a comment below (if applicable) or consult

| Pin | Wire Color | Signal Name | Function | | :--- | :--- | :--- | :--- | | | Red | +B1 | Main EFI Relay Power Input | | A02 | Red | +B | Main EFI Relay Power Input | | A03 | Black/Yellow | IGSW | Ignition Switch ON Signal (12V) | | A04 | - | - | Empty | | A05 | Brown | VTA | Throttle Position Sensor (TPS) Signal | | A06 | Light Green | VCC | TPS Sensor 5V Reference | | A07 | Black | E2 | TPS Ground | | A08 | Blue/Red | PIM | MAP Sensor Signal (0-5V) | | A09 | Red/Blue | THW | Engine Coolant Temp (ECT) Signal | | A10 | White/Black | STA | Starter Signal (from ignition switch) | | A11 | Light Green/Black | VC | Common 5V Sensor Reference | | A12 | Green/Red | VAF (or MAP Sig) | Early models: AFM signal | | A13 | Yellow/Red | KNK | Knock Sensor Signal | | A14 | Red/White | SP1 | Vehicle Speed Sensor (VSS) Input | | A15 | Black/White | E01 | ECU Power Ground (to engine block) | | A16 | Black/White | E02 | ECU Power Ground (to engine block) | | A17 | - | - | Empty | | A18 | Yellow | OX1 | Front Heated Oxygen Sensor (O2) Signal | | A19 | Black/Red | VSV EGR | EGR Vacuum Switching Valve Control | | A20 | Brown/Yellow | ISC1 | Idle Speed Control Valve Coil 1 | | A21 | Brown | ISC2 | Idle Speed Control Valve Coil 2 | | A22 | Light Green/Red | G- | Distributor Pickup Coil (Negative) | | A23 | Light Green | G+ | Distributor Pickup Coil (Positive) | | A24 | Red | NE+ | Distributor RPM Signal (Positive) | | A25 | White | NE- | Distributor RPM Signal (Negative) | | A26 | White/Red | IGF | Ignition Confirmation Signal (to igniter) | Pro Tip: Pins A01 and A02 provide 12V. If your fuel pump doesn’t prime, check these wires first. Pins A15 and A16 are critical grounds—never assume chassis ground is enough. Connector B (16 pins) – Injectors & Ignition This connector handles high-current outputs. You will not see 12V here with the key on

However, when things go wrong—or when you plan a standalone ECU swap or engine conversion—the wiring becomes the biggest headache. The Engine Control Unit (ECU) is the brain, but without a proper , that brain is just a plastic box with two connectors.